The black wire from the ceiling fan is the hot wire that runs the motor and turns the fan blades. The white wire is neutral and completes the fan circuit. The blue wire is the hot wire for the ceiling fan light fixture. The ceiling fan motor does not have a ground wire. The term hard-wired means the cable comes furnished with the product and is physically connected or hardwired into the household wiring.
There is no plug to plug in. All built-in appliances such as; built-in ovens, have conduit with the electrical leads attached to the range. Others also offer light-dimming and thermostatic control capabilities. Turn your Bluetooth Device into a convenient remote control for your ceiling fan.
This universal remote will work with most fans. It comes with a receiver that has to be wired into the fan. It has a light dimmer, three speed settings, and it can be used to turn the fan on and off. Start of suggested clip. Will be connected to the blue wire. Disassembling the Ceiling Fan Open the box and identify the remote receiver. Does a ceiling fan with remote need a wall switch? Can I connect red and black wires together ceiling fan?
Connect the red wire in the ceiling to the black wire in the light kit and the black wire in the ceiling to the black wire in the fan. Tuck the wires back into the box. Turn the power back on and test the fan.
Can you connect red and white wires together? Where does the yellow wire go on ceiling fan with remote? The blue wire from the ceiling fan gets connected to the second live wire from the ceiling. This second wire can vary in color but is most commonly red or black.
This connection allows you to power your lights from the second switch. Connect the white grounded wire from the ceiling to the white wire from the fan. Do ceiling fans have to be hard wired? What does it mean when a ceiling fan needs to be hardwired? How can I get my ceiling fan to work without a remote?
How does a remote control ceiling fan work? A remote control designed for use with a ceiling fan contains a transmitter. When operating properly, the remote transmitter sends a signal to a receiver in the ceiling fan that gives the fan simple instructions. How do you wire a wall fan switch?
Is red wire hot? Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe. What are Green Wires? READ: what color is lexus nightfall mica. When you see two cables entering, and both blacks are already tied together , and both whites are tied together, that circuit is carrying current onward to some other point-of-use.
Which color wires go together? The neutral is white , the hot live or active single phase wires are black , and red in the case of a second active.
Three-phase lines are red, black, and blue. Function Protective ground label PG Color, common bare, green , or green-yellow Color, alternative green What are the wires for a ceiling fan?
Secure the motor to the ceiling bracket with two locking screws. Slightly tug on the wire to make sure none of the wires are loose. Pull chain ceiling fans do not come with a remote receiver of any type. For ceiling fans without a remote receiver, follow these steps to wire your fan. Connect the white grounded wire from the ceiling to the white wire from the fan. Connect the black wire ungrounded from the ceiling to the black and the blue wires from the fan.
Connect the black ungrounded wire from the ceiling to the black wire from the fan. Connect the second ungrounded light wire from the ceiling to the blue wire from the fan. Hunter ceiling fans with preinstalled remote receivers have the receiver built into the ceiling fan body at the factory.
Our engineers innovated this technology to help make wiring a ceiling fan simpler. The remote control cradles can be attached to the wall. You can dock the remotes into the cradles to use them like a switch on the wall, or remove the controls from the cradle and use them as handheld remotes. The light switch powering the ceiling fan will likely be a single or a dual wall switch. Cap the blue wire from the fan. You will not need it for single switch wiring.
If you have a dual wall switch, the steps for connecting the wires with a wire nut will be similar to the above steps. The only difference is instead of capping the end of the blue wire in step 4, you'll use a wire nut to connect the second ungrounded light wire from the ceiling to the blue wire from the fan.
Most Hunter ceiling fans come equipped with either a preinstalled or separate remote receiver. If you're wondering how to wire a ceiling fan with a separate remote receiver, use the wire nuts to:. Connect the black ungrounded wire from the ceiling to the black wire from the receiver. Connect the white grounded wire from the ceiling to both the white wire from the receiver and the white wire from the fan.
Connect the yellow wire from the receiver to the black wire from the fan. Connect the blue wire from the receiver to the blue wire from the fan. If you're installing a ceiling fan that requires a downrod, you'll need to finish installing the canopy.
If you're installing a low profile ceiling fan, you'll need to finish installing the motor housing. Lift the canopy into place, making sure the triangular openings and screw holes are aligned.
Using a screwdriver, insert and securely tighten the canopy screws. A magnetic screwdriver will give you more visibility when securing the canopy. Raise the motor housing up until it's correctly positioned over the motor and ceiling brackets. Rotate the motor housing until the screw holes are aligned with the holes on the bracket. The indentation inside the housing should lock into place with the notch inside the ceiling bracket.
Hold the motor housing in place. Use a screwdriver to insert and tightly secure the four motor housing screws. Your Hunter fan comes with the necessary parts you'll need to install the blades. There are three common blade installation methods for Hunter ceiling fans:. Use the respective screws to attach each blade to the blade irons. Position the blade irons with the motor, making sure all screw holes are properly aligned. Lightly hand-tighten the screws, then use a screwdriver to securely tighten the screws.
Insert the blades into the openings and align the hole openings in the blades with the blade irons. Attach each blade to a blade iron using the three provided blade washers and blade assembly screws. Make sure the screws are secured tightly. Squeeze the blade and the blade iron post together.
Note that the flared tops of the blade iron posts will be fully visible above the blade when properly assembled. To assemble a fan with a lighting kit, first identify if your fan has a Quick Connect feature by examining the switch housing. Hunter Quick Connect fans have a distinct locking mechanism located on the switch housing.
These fans also have a ring that surrounds the switch housing in the middle. Hunter fans without Quick Connect technology do not have either feature. Connect the fan and light fixture plugs together. Make sure to align the colored markings on the connectors.
Push the connectors and the extra wire into the hole located at the top of the light fixture. Carefully connect the light fixture to the bottom of the fan. Make sure the holes on the mounting ring at the top of the fixture are aligned with the spaces in the mounting bracket on the bottom of the fan. While holding the body of the fan still, turn the light fixture clockwise to engage the locking pin. Listen for a clicking sound to verify that the locking pin is securely in place.
After installing the glass, reinstall the light rings into the sockets. Use the socket ring glass tool that came with your fan to turn the light rings clockwise until they're tightened. Choose any two holes in the switch housing mounting plate to screw two of the housing assembly screws halfway.
Feed the wire connector through the center of the upper switch housing. Wrap the keyhole slots around the screws then twist counterclockwise. Use a screwdriver to install the third screw then tighten the remaining two screws. Connect the upper and lower switch housing together using the plug connectors, making sure to line up the colored markings. Locate the notches in the sides of the lower switch housing and align them with the screws located on the upper switch housing.
Lock the switch housing into place by twisting the lower portion clockwise. Using a screwdriver, install the third housing screw.
Tighten all the screws. To install the light shades, first, loosen the thumbscrews. Then, lift each shade to the light fixture and insert and tighten each thumbscrew.
Connect the pull chain pendants to the appropriate short chains coming from the switch housing. Connect the fan and light fixture connectors. Make sure you line up the colored markings on the connectors. Secure the connectors by pushing the connectors and extra wire into the hole located at the top of the light fixture.
This step will ensure that the fan and light fixture are successfully mounted. Carefully lift the light fixture and position it at the bottom of the fan. Make sure the holes on the mounting ring located on the top of the light fixture are aligned with the spaces in the mounting bracket located on the bottom. Listen for the clicking sound to verify the connection is secure. Lift the globe and use the provided three thumb screws to attach it to the light fixture.
Tighten the thumbscrews by hand. Feed the fan pull chain through the hole at the bottom of the light kit. Position both the globe and globe keeper against the metal plate, keeping them flush. Feed the light pull chain through the hole located in the center of the finial cap.
Then, feed the fan pull chain through the hole located in the side of the cap. Feed only the light pull chain through the finial. Attach the finial to the threaded rod and tighten by hand. Attach the short chains coming from the switch housing to the appropriate pull chain pendants. A no-light cap covers the portion of the fan where a light kit would normally be installed. If you'd rather use a no-light cap instead of a light kit, use these steps to properly install it. Remove the two screws on the light kit that connect the light kit to the lower switch housing.
Disconnect the blue and white wires inside the light kit and lower switch housing. To safely cap off wires not being used, install the dummy terminal included with the light cap.
Attach the terminal to the ends of each wire located in the lower switch housing. Use a Phillips head screwdriver to install the switch housing cap with the two switch housing screws you previously removed earlier.
Connect the lower and upper switch housing with the connectors. Make sure you align the colored markings on the connectors. Carefully lift the switch housing and position it at the bottom of the fan. Position the holes on the mounting ring located at the top of the switch housing with the spaces in the mounting bracket located on the bottom of the fan. While holding the body of the fan as still as possible, engage the locking pin by turning the light fixture clockwise.
Listen for a clicking sound to verify the connection is secure. Hunter offers a variety of ceiling fan controls that make it simple to control your fan and light.
Most handheld remotes and wall controls come pre-paired to the ceiling fan. Handheld remotes let you conveniently control your fan's features. Follow these steps to use your handheld ceiling fan remote:.
To change the direction of the fan, press and hold the fan button. To turn the ceiling fan light on and off, press the light button. Press and hold the arrow buttons to enable the dimmable ceiling fan light options. Hold the light button down to dim the ceiling fan light. Wall controls are installed at the wall switch, making it easy to remember where your ceiling fan control is located. Follow these steps to use your wall control. Turn the ceiling fan light on and off by pressing the light button.
Smart fan controls let you use your smart phone or smart home devices to control your ceiling fan. If you've been wondering how to install a ceiling fan, hopefully, this Hunter ceiling fan installation guide will successfully navigate you through the process. Remember that hiring a certified, professional electrician is always an option if you feel uncomfortable with any step listed above.
After your new Hunter ceiling fan is installed, you might need to do some regular ceiling fan maintenance from time to time.
Use our simple ceiling fan installation tips to keep your Hunter fan working in great condition. Hunter Casablanca Industrial. Login Create Account. Close Menu. Submit Search Submit Search. Close search. Ceiling fan installation guide While installing or replacing a ceiling fan might seem complicated, ceiling fan installation is a relatively straightforward process. How to Install a Ceiling Fan? Getting Started 1.
Uninstall and Remove an Existing Fixture 2. Install the Ceiling Bracket 3. Wire the Ceiling Fan 4. Finish Installing the Canopy or Motor Housing 5. Install the Blades 6. Install the Lighting 7. Use the Remote Controls. Copy Embed Code. How to install a ceiling fan video by Hunter Fan. When referring to our ceiling fan installation guide, keep the following in mind: The videos and instructions included within the guide generally apply to the installation of most Hunter fans, however the directions for your specific fan model may differ slightly.
This guide should only be used as supplemental material to the model-specific fan manual included with your purchase of a Hunter ceiling fan. Always refer to your manual for the most accurate instructions for installing your fan. If your manual has been misplaced, you can easily find and download the model-specific manual for your Hunter fan.
As an alternative to DIY ceiling fan installation, you can hire a professional to install your fan. Through Hunter's partnership with HomeAdvisor, the largest home improvement network service in the U.
0コメント