See your Bluetooth phone manual for instructions. When receiving an incoming call, press and hold the call control button for 8 seconds to reject the call. To switch an active call from your phone to your headset, press the call control button for 3 seconds.
To switch an active call from your headset to your phone, press and hold the call control button until you hear a tone.
As the headset moves more than 33 feet 10 metres away from the Bluetooth device or encounters interference:. If any of the above occur, move closer to your Bluetooth device. To order, please contact your Plantronics supplier or go to www. I did not enter my password. Your phone did not locate the headset. Repeat the pairing process on page 7. Incorrect menu selections were made on your mobile phone. The headset is not turned on.
Press the call control button for approximately 2 seconds until you hear a beep or see the indicator light glow blue to turn headset on. Your headset is out of range.
Move the headset closer to the phone or Bluetooth device. Your headset battery is drained. The listening volume is too low. You can also call the technical assistance center for accessibility information. For warranty information, please refer to the included product warranty card or visit www.
Operation is subject to the following two conditions:. This device may not cause harmful interference, and. This device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures:. Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on another circuit. This device and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions: 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device. Visitez le site www. Nous pourrons ainsi vous proposer le meilleur service et le meilleur soutien technique possible. Embouts en gel. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. Insert the headset into the charging pocket. Twist the bottom of the AAA battery charger B anticlockwise and release the battery holder. Insert the battery into the AAA battery holder. Slide the battery holder back into the battery charger and turn clockwise. Snap battery charger onto charging pocket. Ensure that the indentation on the battery charger connector aligns with the shirt clip on the charging pocket. NOTE Do not twist the components apart.
Snap the mini USB charger onto the charging pocket. Option A: Using the vehicle power adapter. Snap the headset charging pocket onto the 1. Begin with headset turned off.
The headset is now in pairing mode for the next 60 seconds. If the headset is either too tight or too loose, remove the mediumsized ear tip from the headset by.
Remove the ear tip from the headset by turning the ear tip to the centre or neutral position and pulling the ear tip away from the headset. Replace the ear tip. To turn the mute off, press both buttons again. Redialling last number To activate last number redial, double press the call control button. Power saving mode Power saving mode temporarily disables the digital signal processing DSP feature of the Discovery and headsets to provide a longer talk time.
Using voice dialling With the headset on, press and hold the call control button for 2 seconds to activate voice dialling.
NOTE To use voice activated dialling, the voice dialling feature must be enabled on your phone. Rejecting a call When receiving an incoming call, press and hold the call control button for 8 seconds to reject the call. Switching a call from phone to headset To switch an active call from your phone to your headset, press the call control button for 3 seconds. Switching a call from headset to phone To switch an active call from your headset to your phone, press and hold the call control button until you hear a tone.
Powering off Red light appears and goes off. Power off — Charging battery Red light flashes every 5 seconds. Battery fully charged Red light goes off. Low battery Red light flashes every second. Pairing mode Red then blue light flashes for seconds Missed call Purple light flashes every 5 seconds.
Press any button to cancel. Ringing Purple light flashes rapidly. This manual is available in the following languages: English. Below, you will find the most frequently asked questions about the Plantronics Discovery Is your question not listed?
User Guide Bluetooth. Ask a question. About the Plantronics Discovery Plantronics Discovery specifications. Related product manuals. Frequently Asked Questions Below, you will find the most frequently asked questions about the Plantronics Discovery When is my volume too loud?
A volume above 80 decibels can be harmful to hearing. When the volume exceeds decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.
Can I make hands-free calls with my Headphone? The newer Headphones generally have a small microphone built in which allows for calling.
0コメント